The washer will not move out of sensing mode into wash mode. Turn the knob until just the "DONE" LED is illuminated. I did the above steps and got sensing, rinse complete and did it again and got sensing, rinse, spin, complete.I did this and the sensing and wash lights flash on together then the complete light flashes and it goes back and forth do you know what the problem is for me?....washer starts to fill them stops...empties water then just sits with the wash light on and nothing elseIf not comfortable trying to diagnose or repair the washer have a good repair tech. Kenmore 25132 4.3 cu. What do I do to correct thisCraig Honeycutt , Use the diagnostic mode on your washer to retrieve error code/s which will aid in finding the problem of machine. Contractor's Assistant: How long has this been going on with your Kenmore washer? (press and hold the start/cancel button for 3 seconds to turn everything off) 2. The high performance electronics repair kit. 1 Questions It is top loading and is about 6 years old. NOTE: AFTER RESET, sequence “a” through “e” must be completed within 6 seconds.RESET - Rotate cycle selector knob counterclockwise to clear sequence.a. Let us know which ,and if, lights appear and let us know.Help.. My washer is acting up. Be sure the washer is in standby mode (plugged in with all indicators off). Links below may aid in diagnosing washers issue, 1st link tells about error codes and how to retrieve them for diagnosing and 2 and 3 links are trouble shooting.These washers with the electronic board in my honest opinion is garbage.

Rotate cycle selector knob clockwise one click and wait 1⁄2 second.c.

I recommend you check all wires and connections/plugs in washer for corrosion, damage, loose. ?here is the sequence you'll need to go through to display the error code.1. Good luck.I hope this helped you out, if so let me know by pressing the helpful button.Have this problem will not go into diagnostic mode pause light flashing can anyone helpMy washer keep adjusting clothes in washer even when clothes are good in it how can I fix it Rotate cycle selector knob clockwise one click and wait 1⁄2 second.b. Perform the following sequence of movement using the cycle selector knob. $839.99. Just bought a brandnew washer from Sears, Kenmore Elite frontload washer Model :970.C4808. Perform the following sequence of movement using the cycle selector knob. I managed to open the door with the cancel button. Rotate cycle selector knob clockwise one click and wait 1⁄2 second.You are now in diagnostics. A collection of guides and support to help with washer repair.Won't start a cycle and the lid lock light is no flashing for an errorTech was just here and replaced pump. Close the door. The washer will not move out of sensing mode into wash mode.Washer won't move from washing mode to next mode. Rotate cycle selector knob counter-clockwise one click and wait 1⁄2 second.e. 2524 Questions 1. It first started fine but it never finished the cicle, the door was locked for some time too. Still not working correctlyI have a Kenmore and all it does is the sensing light flashes? How old is it? April 15th, 2018. Your question was published, help is on its way!

Our kenmore 500 ...? Our kenmore 500 series frontload washer is stuck on sensing what do we do?? Get shopping advice from experts, friends and the community! Contractor's Assistant: Is your Kenmore washer top or front loading? Kenmore series 500 washer is stuck on " sensing" and therefore I cannot wash. Can you help? (press and hold the start/cancel button for 3 seconds to turn everything off)2.

Open the washing machine door and check to make sure that no small garments are blocking the door from latching completely. Share it! ft. Top Load Washer ... Sold by Sears.com. $579.99. Be sure the washer is in standby mode (plugged in with all indicators off). It never finished the cycle and drained the water. Opening and closing the washer door will reset the machine, and the machine will not run unless the door is completely closed. - Kenmore 11o.20222510 Find below links on how to retrieve error codes and an error code explanation/troubleshoot link. What have you tried so far? have a look and diagnose and estimate repair. Report This by Amy Hammond.

Rotate cycle selector knob clockwise one click and wait 1⁄2 second.d. Push START.Turn the dial one click to see the error code that is displayed by the LED's along the progress line. NOTE: AFTER RESET, sequence “a” through “e” must be completed within 6 seconds.